freiberufler Lead Piping Engineer (Design/Layout) / Piping Support Engineer auf freelance.de

Lead Piping Engineer (Design/Layout) / Piping Support Engineer

offline
  • auf Anfrage
  • 10559 Berlin
  • Europa
  • tl  |  en
  • 07.05.2020

Kurzvorstellung

Eleven years of experience in the field of Oil and Gas Industry (On-shore/Offshore), Petrochemical Plant, Sulfur Plant and Power Plant. Worked as a Lead Piping Engineer using 3D Software tools (PDMS/PDS/Cadwordx Plant Design/AutoCAD Plant 3D)

Qualifikationen

  • 2D-CAD
  • 3D-CAD
  • 3DESIGN
  • CAD (computer-aided design)

Projekt‐ & Berufserfahrung

Lead Piping Designer
Jacobs Belgie N.V., Terneuzen
9/2018 – offen (5 Jahre, 7 Monate)
Chemieindustrie
Tätigkeitszeitraum

9/2018 – offen

Tätigkeitsbeschreibung

Period September 2018 – Present
Company Jacobs Belgie N.V
Position Lead Piping Designer (PDMS)
Project FA-2017 Repair Tank Dow Chemicals Plant (Project in Terneuzen, Netherlands)
Main Responsibilities:
• Developing layouts and conducting reviews to consider constructability, operability and maintainability of the facility.

Project FB-203 Bypass Tank Dow Chemicals Plant (Project in Terneuzen, Netherlands)
Main Responsibilities:
• Evaluate the scope of work using P&ID’s and specifications to design piping systems while adhering to plant design standards.
• Complete equipment layout, piping layout, piping isometrics and general arrangement drawings.
• Conduct necessary fieldwork inclusive of walk downs of current systems, locate tie-in points and measuring.

Project D-771 Tank Repair Dow Chemicals Plant (Project in Terneuzen, Netherlands)
Main Responsibilities:
• Responsible for overseeing and designing of all pipes involve in tank repair
• Field visits for checking/measuring the actual condition of the plant, locating tie-in points and preparing preliminary designs.
• Develop preliminary Bill of Materials with respect to piping design.

Eingesetzte Qualifikationen

3D-CAD

Senior Piping Design Engineer / Senior Piping Checker
ARCUS GmbH & Co., Berlin Germany
11/2017 – 9/2018 (11 Monate)
Bauwirtschaft, Anlagen- und Schiffbau
Tätigkeitszeitraum

11/2017 – 9/2018

Tätigkeitsbeschreibung

• Responsible for the checking of overall piping layout/design.
• Responsible for the checking of support types (primary and secondary).
• Responsible for the basic design and detail planning of piping and its specifications.
• Responsible to assist the designers/drafters.

Eingesetzte Qualifikationen

3DESIGN, CAD (computer-aided design)

Lead Piping Engineer
KNM Process Systems Sdn Bhd Malaysia, Kuala Lumpur
6/2015 – 4/2017 (1 Jahr, 11 Monate)
Öl- und Gasindustrie
Tätigkeitszeitraum

6/2015 – 4/2017

Tätigkeitsbeschreibung

Period June 2015 – April 2017
Company KNM Process Systems Sdn. Bhd. -Malaysia
Position Lead Piping Engineer
Project Peterborough Green Energy Project (Project in United Kingdom)
Main Responsibilities:
• Responsible for issuance of all documents regarding Piping Specification, Valve Specification and Pipe Support Specification.
• Responsible for Issuance of Piping Material Take-Off.
• Responsible for Overall Piping and Equipment Layout and General Arrangement Drawing.
• Responsible for the study of Material Handling Equipment.
• Responsible for issuance of Piping Isometrics and Technical Bid Evaluation.
• Responsible to check the Standard and Special Piping Support.
• Responsible to check and monitor the progress of Stress Report.
• Responsible for the preparation of 3D model for 30%, 60% and 90% model review.

Project Sulfur Recovery Unit for Heavy Residue Conversion Complex (Project in Russia)
Main Responsibilities:
• Responsible for any piping modification in Construction by correcting it and issue as “As-built dwg”.
• Responsible to do the line checking for every piping if it is erected as per isometrics and P&ID.
• Responsible to assist the Contractor/Fabricator on which type of Standard Support to be used.
• Responsible to assess and identify the Variation Order (VO).
• Responsible for piping and equipment layout/design using CADworx Plant Design software.
• Review and check the Preliminary Vendor drawings, Mechanical and Process Data Sheet.

Eingesetzte Qualifikationen

3DESIGN

Senior Piping Design Engineer
Amec Foster Wheeler, Kuala Lumpur
12/2014 – 6/2015 (7 Monate)
Öl- und Gasindustrie
Tätigkeitszeitraum

12/2014 – 6/2015

Tätigkeitsbeschreibung

Period December 2014 – June 2015
Company Amec Foster Wheeler Malaysia
Position Senior Piping Design Engineer (PDS)
Project NGC Beachfield CHS Facility (Project in Trinidad and Tobago)
Main Responsibilities:
• Responsible for piping design/layout and equipment layout under CHS area using PDS software.
• Clash check and review for resolution for all clashes using Smart Plant Review.
• Review and check the Preliminary Vendor drawings, Mechanical and Process Data Sheet.
• Coordinate, assist, monitor and report the progress to Lead Piping Engineer.

Project BD Storage Terminal (Project in Johor, Malaysia)
Main Responsibilities:
• Responsible for piping design/layout for BD pump, BD cooler, Glycol Area and Air Receiver Area using 2D AutoCAD.
• Produce piping isometrics using 2D AutoCAD

Eingesetzte Qualifikationen

3DESIGN

Senior Piping Design Engineer
Technip FMC, Kuala Lumpur
4/2008 – 7/2014 (6 Jahre, 4 Monate)
Öl- und Gasindustrie
Tätigkeitszeitraum

4/2008 – 7/2014

Tätigkeitsbeschreibung

Period April 2008 –July 2014
Company Technip-FMC Malaysia
Position Senior Piping Design Engineer (PDMS/MDS)
Project Malikai EPC TLP Project (Project in Malaysia)
Main Responsibilities:
• Responsible for piping design/layout of water lines systems, which consist of Cooling Water Return, Cooling Water Supply and Water Injection. Also involved for Process Lines such as Process Gas and Vent to Flare Lines system. Any issue on the P&ID and layout which involved the Process Group need to discuss before doing some mark-up and implementing it in the 3D model.
• Responsible to check and model the equipment using the information on Vendor Drawing.
• Provide initial Pipe Support for all lines using Multi-Discipline Support (MDS).
• Provide Piping Isometrics using PDMS Isodraft for the Stress Analysis and Material Take-Off.

Project Wheatstone Upstream Project (Project in Australia)
Main Responsibilities:
• Responsible for all Piping design/layout at Intermediate Deck and Flare Book area. Majority of the lines involved are Process Gas Systems (Gas Hydrocarbon, Liquid Hydrocarbon, Produced Water, Process Liquid and Vapor), Drain Systems (Closed, Open and Hazardous Drain) and Flare Lines Systems. By checking the P&ID, all necessary line slopes, instrumentation, valves and SP item must be modeled in 3D PDMS model with the consideration of every piping component requirement.
• Coordinating with the Stress Engineer in Perth office for the requirement of Compressor Lines and modeling each support as per pipe loads given.
• Working with the Structural Engineer for the VIV loads analysis on HP and LP Flare lines.

Project Gumusut-Kakap Topside Detailed Engineering Project (Project in Malaysia)
Main Responsibilities:
• Responsible for Piping design/layout at Process Area. Lines involved are Compressor lines, Deluge lines and Cooling Water lines.
• Clashed check executions, screening and solution using PDMS model.
• Re-route/revised lines base on the new sets of P&ID and as per comments during model review.
• Model pipe supports based on Stress requirements using Multi-Discipline Support (MDS).
• Generation of Isometrics using PDMS Isodraft and resolution of Isometrics failure.
• Special Pipe Support modeling in 3D using PDMS and extracting it to 2D AutoCAD.


Project FEED for SHWE Field Development Project (Project in Myanmar)
Main Responsibilities:
• Developed 2D background coordinate drawings in AutoCAD for plot plan development, 3D environment in PDMS for piping and equipment general arrangements.
• Develop conceptual layout during early stages of plot plan development.
• Study and modify piping components in Piping systems with coordination of Engineering and Planning groups.
• Run a program for checking the status, connectivity, database, reliability and interference on model design files. Generate 2D drawing using PDMS draft.

Eingesetzte Qualifikationen

3DESIGN

Piping Design Engineer
IHI Philippines Corporation, Manila
4/2007 – 4/2008 (1 Jahr, 1 Monat)
Öl- und Gasindustrie
Tätigkeitszeitraum

4/2007 – 4/2008

Tätigkeitsbeschreibung

Period April 2007 –April 2008
Company IHI Philippines, Inc.
Position Piping Design Engineer (PDMS)
Project GP1Z LNG Project (Project in Algeria)
Main Responsibilities:
• Responsible for 3D modeling of Equipment and Piping using PDMS.
• Prepare Pipe support design based on standard and flexibility calculation analysis.
• PDMS Drafting for Piping Arrangement Drawing, PDMS Isodraft of Pipes for fabrication drawing.
• Coordinate, assist, monitor and report area progress to Area Lead.

Project Toho Gas Plant Project (Project in Japan)
Main Responsibilities:
• Prepare detailed piping route design and supports.
• Responsible for the preparation, extraction and checking of Detail drawings in accordance with respective client specification and codes.
• Preparing and reviewing piping job specs and materials for conformity to job requirements. Coordinate with other Engineer to make changes to Pipe Specifications as required.
• Prepare PDMS 3D model, Isometric drawing, General Arrangement and Material Take Off.

Eingesetzte Qualifikationen

3DESIGN

Zertifikate

Registered Mechanical Engineer
2005

Ausbildung

MBA Energy Management
MBA
2017
TU-Berlin
Bachelor of Science in Mechanical Engineering
Bachelor
2005
Polytechnic University of the Philippines

Über mich

Dear Sir/Madam:

I am interested to apply for the position you have posted on your website. As for my educational background, I am currently an MBA student at TU-Berlin for the program Energy Management. I am also graduated as a scholar at the Polytechnic University of the Philippines with a degree of Bachelor of Science in Mechanical Engineering. With the same year, I passed the national exam and became a Registered Mechanical Engineer.

I have 11 years of experience in the field Piping Design/Layout and hold the position Senior Piping Design Engineer at Arcus Gmbh and Company. I’ve worked for nine years in Kuala Lumpur, Malaysia with various International and Engineering companies. I was also assigned in Russia for six months to supervise the construction team. At the moment, I am currently employed in one the Engineering Consulting companies here in Berlin Germany. It would be an honor if you give me the opportunity to take this position.

I appreciate you taking the time to look over my application and enclosed documents. Any further information you need, please do not hesitate to contact me. I look forward to your positive response.


Sincerely yours

Weitere Kenntnisse

Eleven years of experience in the field of Oil and Gas Industry (On-shore/Offshore), Petrochemical Plant, Sulfur Plant and Power Plant. Worked as a Lead Piping Engineer using 3D Software tools (PDMS/PDS/Cadwordx Plant Design/AutoCAD Plant 3D) and familiar with International Codes and Standards. Work experience includes Piping, Structure and Equipment modeling, Piping Design/Layout and Pipe Support. I have worked for nine years in Kuala Lumpur, Malaysia, six months in Tatarstan, Russia and currently employed as a Senior Piping Design Engineer/Senior Piping Checker in Berlin, Germany

Persönliche Daten

Sprache
  • Englisch (Fließend)
  • Philippinisch (Muttersprache)
Reisebereitschaft
Europa
Arbeitserlaubnis
  • Europäische Union
Profilaufrufe
2886
Alter
39
Berufserfahrung
17 Jahre und 11 Monate (seit 04/2006)
Projektleitung
11 Jahre

Kontaktdaten

Nur registrierte PREMIUM-Mitglieder von freelance.de können Kontaktdaten einsehen.

Jetzt Mitglied werden